It’s a simple matter to trim that top fillet flush with the face of the neck. Since I haven’t filled the truss rod channel completely, I decide to make use of it to guide my router (Dremel tool mounted in a router base). I left this insert fillet purposely high because I have a fiendish plan. Guitar necks, especially on older guitars, can sometimes form a warp or twist from years of string tension while being stored in hot attics, closets or anywhere it gets hot enough to soften the glue under the fretboard. Then the truss rod can be reinstalled and the second section of fillet glued in over it. Some additional strength, I think. So, let’s fix the channel. Nothing much moving. On a regular, unbound, neck, the wood of the fingerboard runs from edge to edge along the neck. This increase the action at the 12th fret from 5/64" to 7/64" (measuring from the 6th string with a capo on the 1st fret), which was quiet noticeable when playing the guitar. While I’m confident that the newly curved truss rod will operate well, I want to give this neck every chance of remaining straight against string-tension. It’s composed of two pieces: 1) the base and 2) the sled. A little glue and clamping does the trick. Carbon fibre neck reinforcement installed in Gibson ES-335 guitar. Basically the guitar absorbed too mush moister, which made the neck bend upward right at the heal, (where the neck joins the body). What if I straightened the neck before I glued in these new fillets? I don't do spam and you can unsubscribe at any time. It's not that scary. Wrap an old t-shirt or sheet over the neck of the guitar. This all contributes to everything staying that way after the guitar's removed from the jig. Then I shaped the bottom of the fillet to match the odd profile at the bottom of the channel. Removing the Frets from the Neck 1. Right; easy part, done. The router will cut a nice new channel parallel to the truss rod channel. So, if you look along the side of your guitar or bass neck, chances are you’ll see twenty-something little slots that were cut into the fingerboard. Check your inbox for an email for me—you'll need to confirm your subscription there. I removed the fingerboard to access the neck face beneath and then removed the wood fillet keeping the truss rod in place. This will raise the rod up and provide some much-needed mass behind it. I thicknessed a piece of maple to fit the truss rod channel. Phone: (757) 582 0525Address3612 Ithaca TrailSuffolk VA 23435, Copyright © 2010-2020 Accu-Tech Guitar Repair LLC | Terms of Use | Privacy Policy. The 3.2 x 8.2mm (.125” x .325”) size is good for adding a reinforcing strip along either side of the truss rod. Warm up your iron and set it to its hottest setting. Simple mod to speed up working with the Erlewine Neck Jig. Set up two bench clamps approximately 12 inches apart. I strapped the guitar into the Erlewine Neck Jig and used it to pull and hold the neck in a straight position. They’re light and strong and work well. But, thing is, the music shop said it would be well over £220. Made from Aluminum this jig allows for precise neck alignment and control giving you a perfect neck joint. My former tech & fav builder, Eric Daw, pinupcustomguitars.com, has a heated neck straightening jig. This means that the fret slots also run from edge to edge. Lay your guitar flat, face up on your work table. And dig, I did. Ever hear someone say: "I'll do anything else with my guitar but I won't touch the truss rod."? Fretting / Fretwork Jig. Let me illustrate what I mean here. However, in order to comply with privacy regulations, I also need you to provide consent to store and process the information you've entered. Installing corrective fillet and truss rod on warped neck Gibson guitar. In my ever so humble opinion, you have a few more years to go before you don't have to worry as much about future warping. , This article written by Gerry Hayes and first published at hazeguitars.com, Tagged: guitar, bass, repair, luthier, warp, bow, neck, neck deformation. The Edge vise is specifically designed to work with the jig, it also doubles as a end graft tool. I should note that all of this routing and glueing was done while the neck was held straight in the neck jig. After setting up the jig, I use a fretboard heat blanket to soften the glue under the fretboard... Centering under the lowest point of a warp with a threaded neck brace, I can level the neck to its original position with the truss rod loosened. Prepare your tools and guitar. And, let’s face it, what more can we ask for? Adjust both clamps to the same height as the distance between the guitar neck and the bench. First order of business is to repair the damage caused when the truss rod broke through the rear of the neck. Don’t forget that our neck’s taken on quite a bow and I need to keep that in mind as I proceed. There’s a fair chance that adding that second maple fillet would give me an even closer result but I’m all about playing things safe on this repair. Check out Part 1 and Part 2 for more info if you're just joining us. The bottom section of the fillet will be glued into the channel. I can worry about finish on it later on because I’ll be touching up around the fingerboard too. It might take a few minutes to come through so, don't worry if it's not there immediately. GMC Luthier Tools Specialise in High Quality Guitar Making & Fretting Tools. The Neck Angle Jig has become the industry standard in guitar building tools. I left the guitar aside for a couple of days to see how it settled, just in case I needed to do anything additional before putting the fingerboard back on. The sled moves along the rails while the router moves within the sled The depth of the cut is achieved by changing the router bit depth.
Primitive Root Of 19, Penelope Animal Crossing: New Horizons, Houses For Rent Under $1000 Mcdonough, Ga, Thermo Fisher Scientific Uk, Ophelia Among The Flowers, Ooh Ooh Ooh Yeah Yeah Yeah Rap Song Tik Tok, Watercress Meaning In Punjabi,